Pistol holders allow you to store your pistols in your STACK-ON cabinet's door!
Interior of STACK-ON cabinet Left Hand door depicted above. Note where the hinge jamb and the latch are
Have a STACK ON Gun Cabinet?
If its a single door unit, its probably a Left Hand (LH) door.
If its a two door unit, one door is Left Handed the other is right.
So if you want to use the door for extra storage, We can help! If the gap between the folded metal jam and the 'Hat track' reinforcement/stiffener is close to 8.5" or just a little over, our organizers can fit!
Note: The M&P Shield holder is for all models of M&P Shield (1.0, 2.0, 45, 40, 9mm, EZ, 380 EZ etc)... Though I have not been able to test it with a M&P Shield Plus (I suspect it will hold the pistol but may have trouble with the magazines... you may want to try a 9-40 Poly for the Shield Plus)
Please see the illustration of the doors these were designed to fit:
If its a single door unit, its probably a Left Hand (LH) door.
If its a two door unit, one door is Left Handed the other is right.
So if you want to use the door for extra storage, We can help! If the gap between the folded metal jam and the 'Hat track' reinforcement/stiffener is close to 8.5" or just a little over, our organizers can fit!
Note: The M&P Shield holder is for all models of M&P Shield (1.0, 2.0, 45, 40, 9mm, EZ, 380 EZ etc)... Though I have not been able to test it with a M&P Shield Plus (I suspect it will hold the pistol but may have trouble with the magazines... you may want to try a 9-40 Poly for the Shield Plus)
Please see the illustration of the doors these were designed to fit:
9-40 Polymer Pistol Holder with three mags, note the standard door trays and shell holders in the distance
The 1911 pistol holder show with 2 of three mags spots filled (holds three mags)
Smith & Wesson M&P Shield holder for LH STACK-ON cabinet door shown above. Note that the pistol wants to tip into the hinge: a Bumper will come with the holder to prevent metal to metal contact.
Ruger MKII with 3 magazines in STACK-ON cabinet door
Suggestions for organizing pistols other than what is named here (these fits aren't perfect, but they are workable):
Large, Full sized/ Duty Sized double stacked 9mm/40cal service pistols
- Beretta 92 --> 9-40 Poly Pistol
- Single stack compact 9mm & 40 Cal pistols: M&P Shield
(If you have more suggestions, or questions please contact us and we'll update/advise as we can)
Large, Full sized/ Duty Sized double stacked 9mm/40cal service pistols
- Beretta 92 --> 9-40 Poly Pistol
- Single stack compact 9mm & 40 Cal pistols: M&P Shield
(If you have more suggestions, or questions please contact us and we'll update/advise as we can)
This tool comes with the pistol holders to help you locate and drill the requisite hole in the hinge jamb of the door
INSTALLATION:
Our door organizers do require some holes to be located, drilled, and de-burred to rivet them in place. We'll send the requisite rivets, washers, a hole locator tool, #11 drill bit, and screws as detailed in the instructions with every item purchased. Installers will need a drill, level, and other tools (see the installation instructions for the details)
To make a purchase click on the circle next to the item, check the quantity, then add it to your cart.
Repeat adding items to your cart until you have everything you need, and then check out.
Our door organizers do require some holes to be located, drilled, and de-burred to rivet them in place. We'll send the requisite rivets, washers, a hole locator tool, #11 drill bit, and screws as detailed in the instructions with every item purchased. Installers will need a drill, level, and other tools (see the installation instructions for the details)
To make a purchase click on the circle next to the item, check the quantity, then add it to your cart.
Repeat adding items to your cart until you have everything you need, and then check out.
This bumper snaps into the hinge jamb so that pistol's sights can be kept from metal to metal contact with the cabinet door
What other items do we offer?
Barrel Spacers for Stack On Cabinets
Custom Barrel Spacers - for other cabinet/gun room projects
Scope Standoffs for Barrel Spacers
Shell Holders - for Stack On Cabinet Doors
Door Trays - for storing all kinds of stuff in STACK-ON Cabinet Doors
Pmag Holder - for STACK-ON Cabinet Doors
Pmag Holder - Screw to Wall/board
You can read more about this in the Badger's Den: Click here to read the article I wrote about these!
Barrel Spacers for Stack On Cabinets
Custom Barrel Spacers - for other cabinet/gun room projects
Scope Standoffs for Barrel Spacers
Shell Holders - for Stack On Cabinet Doors
Door Trays - for storing all kinds of stuff in STACK-ON Cabinet Doors
Pmag Holder - for STACK-ON Cabinet Doors
Pmag Holder - Screw to Wall/board
You can read more about this in the Badger's Den: Click here to read the article I wrote about these!
Got a cabinet with two doors? All the stuff on this page for its left handed door here. So for the other door you'll need to Click here for Right Hand Door storage organizers. Not sure what hand door your cabinet has?
The door swing diagram may help understand what door to shop for. What is not obvious to persons unfamiliar with door nomenclature, is that the door on the right side of a person standing in front of the cabinet is the Left Handed (LH) door.
One way to understand door swing nomenclature (on out swing doors) is to imagine standing outside of the room/box/cabinet that the doors enclose, then to place one hand on the hinge, and the other on the lock set. The door is named for the hand that rests on the lock set.
Another way is to imagine your spine pressed up against the jamb where the hinge is mounted. One arm would be able to reach into the cabinet, the other would have its shoulder on the hinge and be able to swing the door without reaching across your body... the one that swings the door is what the door is named for. Or... you can just look at the pictures, look at your cabinets and write down what hand doors you have
The door swing diagram may help understand what door to shop for. What is not obvious to persons unfamiliar with door nomenclature, is that the door on the right side of a person standing in front of the cabinet is the Left Handed (LH) door.
One way to understand door swing nomenclature (on out swing doors) is to imagine standing outside of the room/box/cabinet that the doors enclose, then to place one hand on the hinge, and the other on the lock set. The door is named for the hand that rests on the lock set.
Another way is to imagine your spine pressed up against the jamb where the hinge is mounted. One arm would be able to reach into the cabinet, the other would have its shoulder on the hinge and be able to swing the door without reaching across your body... the one that swings the door is what the door is named for. Or... you can just look at the pictures, look at your cabinets and write down what hand doors you have
We print in PETG (strong and food safe plastic). FYI water bottles are made out of PET. (PETG is PET that is modified to work in a 3D printer). It can take hot rides in cars, and such, but I wouldn't lean a hot barrel nor hot suppressor against it.
We will ship these to Canada per our Terms of Use
PLEASE REMEMBER: It will take at least one business day per item to print. We'll ship your entire order when it is complete.
Typically these are made in grey. But we may need to print in another color... I'd bet your items won't mind what color they lean against. If you have to have grey, please tell us in the note to seller portion of your check out. A hard color request may delay your order by many weeks as we get the color filament you want. We may ignore hard color requests altogether. It really just depends what color filament is on the shelf and what our reorder/delivery schedule is like. Bottom line is: These usually come in grey but sometimes they are black.
Got a 3D printer and want to make them for your own personal use? We offer a license for personal use printing, click here to go to our listing to purchase an EULA.
We will ship these to Canada per our Terms of Use
PLEASE REMEMBER: It will take at least one business day per item to print. We'll ship your entire order when it is complete.
Typically these are made in grey. But we may need to print in another color... I'd bet your items won't mind what color they lean against. If you have to have grey, please tell us in the note to seller portion of your check out. A hard color request may delay your order by many weeks as we get the color filament you want. We may ignore hard color requests altogether. It really just depends what color filament is on the shelf and what our reorder/delivery schedule is like. Bottom line is: These usually come in grey but sometimes they are black.
Got a 3D printer and want to make them for your own personal use? We offer a license for personal use printing, click here to go to our listing to purchase an EULA.