- Our Products
- >
- Gift Ideas
- >
- Helpful Extras
- >
- Shell Holders
Shell Holders
SKU:
$10.00
10
11.99
$4.99 - $5.99
$4.99
On Sale
Unavailable
per item
Sold out
ONLY AVAILABLE AT OUR NEW WEBSITE: Badger-Ridge.com
3D printed shell holders for Wall mount or STACK-ON gun cabinet doors (LEFT HANDED DOORS)
We can make the same shell/ammo holders to mount to the wall (with screws you provide) or into the door of a Stack On gun cabinet (we will provide rivets, you will need to drill holes and pull the rivets, etc).
Select the mounting style you need above.
Select the mounting style you need above.
Have a STACK ON Gun Cabinet? If its a single door unit, its probably a left hand door. If its a two door unit, one door is Left Handed the other is right. So if you want to use the door for extra storage, We can help! If the gap between the folded metal jam and the 'Hat track' reinforcement/stiffener is close to 8.5" or just a little over, our organizers can fit! Please see the illustration below for the doors these were designed to fit:
The items listed here are designed to fit the standard LEFT HANDED STACK-ON door with about 8.5" between the stiffener inside the door and the hinge jamb.
Left Hand Doors in STACK-ON cabinets are the most common from my experience (typically found on single door cabinets). So we offer the most items for Left Handed doors.
We sell shell holders for different calibers. You can see in the picture the 410-45LC holder, 20 Ga holder, and two 12 Ga Holders. (top to bottom). We do make these in 12Ga for right handed doors.
The Stack-On cabinet door organizers do require some holes to be located, drilled, and de-burred to rivet them in place. We'll send the requisite rivets, washers, a hole locator tool, and screws as detailed in the instructions with every item purchased. Installers will need a #11 drill bit, drill, level, and other tools (see the installation instructions for the details)
To make a purchase select an item in the drop down above, check the quantity, then add it to your cart. Repeat until you have everything you need and then check out.
What other items do we offer?
Barrel Spacers
Scope Standoffs
Left Hand Door storage trays
Pistol Holders
You can read more about this in the Badger's Den: Click here to read the article I wrote about these!
Left Hand Doors in STACK-ON cabinets are the most common from my experience (typically found on single door cabinets). So we offer the most items for Left Handed doors.
We sell shell holders for different calibers. You can see in the picture the 410-45LC holder, 20 Ga holder, and two 12 Ga Holders. (top to bottom). We do make these in 12Ga for right handed doors.
The Stack-On cabinet door organizers do require some holes to be located, drilled, and de-burred to rivet them in place. We'll send the requisite rivets, washers, a hole locator tool, and screws as detailed in the instructions with every item purchased. Installers will need a #11 drill bit, drill, level, and other tools (see the installation instructions for the details)
To make a purchase select an item in the drop down above, check the quantity, then add it to your cart. Repeat until you have everything you need and then check out.
What other items do we offer?
Barrel Spacers
Scope Standoffs
Left Hand Door storage trays
Pistol Holders
You can read more about this in the Badger's Den: Click here to read the article I wrote about these!
Got a cabinet with two doors? All the stuff on this page for its left handed door here. So for the other door you'll need to Click here for Right Hand Door storage organizers. Not sure what hand door your cabinet has?
The door swing diagram may help understand what door to shop for. What is not obvious to persons unfamiliar with door nomenclature, is that the door on the right side of a person standing in front of the cabinet is the Left Handed (LH) door.
One way to understand door swing nomenclature (on out swing doors) is to imagine standing outside of the room/box/cabinet that the doors enclose, then to place one hand on the hinge, and the other on the lock set. The door is named for the hand that rests on the lock set.
Another way is to imagine your spine pressed up against the jamb where the hinge is mounted. One arm would be able to reach into the cabinet, the other would have its shoulder on the hinge and be able to swing the door without reaching across your body... the one that swings the door is what the door is named for. Or... you can just look at the pictures, look at your cabinets and write down what hand doors you have.
The door swing diagram may help understand what door to shop for. What is not obvious to persons unfamiliar with door nomenclature, is that the door on the right side of a person standing in front of the cabinet is the Left Handed (LH) door.
One way to understand door swing nomenclature (on out swing doors) is to imagine standing outside of the room/box/cabinet that the doors enclose, then to place one hand on the hinge, and the other on the lock set. The door is named for the hand that rests on the lock set.
Another way is to imagine your spine pressed up against the jamb where the hinge is mounted. One arm would be able to reach into the cabinet, the other would have its shoulder on the hinge and be able to swing the door without reaching across your body... the one that swings the door is what the door is named for. Or... you can just look at the pictures, look at your cabinets and write down what hand doors you have.
We print in PETG (strong and food safe plastic). FYI water bottles are made out of PET. (PETG is PET that is modified to work in a 3D printer). It can take hot rides in cars, and such, but I wouldn't lean a hot barrel nor hot suppressor against it.
PLEASE REMEMBER: It will take at least one business day per item to print. We'll ship your entire order when it is complete.
Typically these are made in grey. But we may need to print in another color... the Pmag holders come in either black or grey. I'd bet your items won't mind what color they lean against. If you have to have grey, please tell us in the note to seller portion of your check out. A hard color request may delay your order by many weeks as we get the color filament you want. It really just depends what color filament is on the shelf and what our reorder/delivery schedule is like. These could come in grey or black.
PLEASE REMEMBER: It will take at least one business day per item to print. We'll ship your entire order when it is complete.
Typically these are made in grey. But we may need to print in another color... the Pmag holders come in either black or grey. I'd bet your items won't mind what color they lean against. If you have to have grey, please tell us in the note to seller portion of your check out. A hard color request may delay your order by many weeks as we get the color filament you want. It really just depends what color filament is on the shelf and what our reorder/delivery schedule is like. These could come in grey or black.